Nick: NeoTheFox
E-mail: soniczerops@gmail.com
Board: HP Compaq 8200 Elite SFF PC
Contents: 
flashrom v1.2 on Linux 5.4.78 (x86_64)
flashrom is free software, get the source code at https://flashrom.org

flashrom was built with libpci 3.7.0, GCC 9.3.0, little endian
Command line (10 args): flashrom -p internal -c MX25L6406E/MX25L6408E -w coreboot.rom --ifd -i bios -V
Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
Initializing internal programmer
/sys/class/mtd/mtd0 does not exist
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: 1c.
Found chipset "Intel Q67" with PCI ID 8086:1c4e.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc25: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching disabled, caching enabled, 
BIOS_CNTL = 0x02: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
Warning: Setting Bios Control at 0xdc from 0x02 to 0x01 failed.
New value is 0x02.
SPIBAR = 0x00007f580f22f000 + 0x3800
0x04: 0xc008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=0, FDV=1, FLOCKDN=1
SPI Configuration is locked down.
The Flash Descriptor Override Strap-Pin is set. Restrictions implied by
the Master Section of the flash descriptor are NOT in effect. Please note
that Protected Range (PR) restrictions still apply.
Reading OPCODES... done
0x06: 0x0000 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0
0x50: 0x0000ffff (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff
0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write.
0x58: 0x07ff0510 FREG1: BIOS region (0x00510000-0x007fffff) is read-write.
0x5C: 0x050f0003 FREG2: Management Engine region (0x00003000-0x0050ffff) is read-write.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.
0x74: 0x87ff07f0 PR0: Warning: 0x007f0000-0x007fffff is read-only.
At least some flash regions are write protected. For write operations,
you should use a flash layout and include only writable regions. See
manpage for more details.
0x90: 0x84 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0xf97f10 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=1
0x94: 0x0006     (PREOP)
0x96: 0x043b     (OPTYPE)
0x98: 0x05200302 (OPMENU)
0x9c: 0x0000019f (OPMENU+4)
0xa0: 0x00000000 (BBAR)
0xc4: 0x00802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xc8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xd0: 0x00000000 (FPB)
OK.
The following protocols are supported: SPI.
Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017
Found Macronix flash chip "MX25L6406E/MX25L6408E" (8192 kB, SPI) mapped at physical address 0x00000000ff800000.
Chip status register is 0x00.
Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set
Chip status register: Bit 6 is not set
Chip status register: Block Protect 3 (BP3) is not set
Chip status register: Block Protect 2 (BP2) is not set
Chip status register: Block Protect 1 (BP1) is not set
Chip status register: Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
This chip may contain one-time programmable memory. flashrom cannot read
and may never be able to write it, hence it may not be able to completely
clone the contents of this chip (see man page for details).
Reading ich descriptor... done.
Peculiar firmware descriptor, assuming Ibex Peak compatibility.
Using region: "bios".
coreboot last image size (not ROM size) is 8388608 bytes.
Manufacturer: HP
Mainboard ID: HP Compaq 8200 Elite SFF PC
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0... 0x510000-0x510fff:ETransaction error!
SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0
SSFC: SCGO=0, ACS=1, SPOP=0, COP=2, DBC=0, SME=0, SCF=1
Running OPCODE 0x20 failed at address 0x510000 (payload length was 0).
spi_write_cmd failed during command execution at address 0x510000
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 1... 0x510000-0x51ffff:EInvalid OPCODE 0x06, will not execute.
spi_write_cmd failed during command execution at address 0x510000
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 2... 0x510000-0x51ffff:EInvalid OPCODE 0x06, will not execute.
spi_write_cmd failed during command execution at address 0x510000
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 3... 0x000000-0x7fffff:RREInvalid OPCODE 0x06, will not execute.
spi_simple_write_cmd failed during command execution
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 4... 0x000000-0x7fffff:RREInvalid OPCODE 0x06, will not execute.
spi_simple_write_cmd failed during command execution
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 5... not defined. Looking for another erase function.
Trying erase function 6... not defined. Looking for another erase function.
Trying erase function 7... not defined. No usable erase functions left.
FAILED!
Uh oh. Erase/write failed. Checking if anything has changed.
Reading current flash chip contents... done.
Good, writing to the flash chip apparently didn't do anything.
This means we have to add special support for your board, programmer or flash
chip. Please report this on IRC at chat.freenode.net (channel #flashrom) or
mail flashrom@flashrom.org, thanks!
-------------------------------------------------------------------------------
You may now reboot or simply leave the machine running.
Restoring MMIO space at 0x7f580f2328a0
Restoring PCI config space for 00:1f:0 reg 0xdc