Nick: PaulePanter E-mail: none Board: unknown Contents: flashrom v1.1-rc1-128-g568f1d3 on Linux 5.5.0-rc6.mx64.310 (x86_64) flashrom was built with libpci 3.5.6, GCC 7.5.0, little endian Command line (5 args): /home/pmenzel/src/flashrom/flashrom -p internal -V -o dell-optiplex-990-a07-flashrom-verbose.log Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns). Initializing internal programmer /sys/class/mtd/mtd0 does not exist No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Mini Tower" DMI string system-manufacturer: "Dell Inc." DMI string system-product-name: "OptiPlex 990" DMI string system-version: "01" DMI string baseboard-manufacturer: "Dell Inc." DMI string baseboard-product-name: "06D7TR" DMI string baseboard-version: "A00" Found chipset "Intel Q67" with PCI ID 8086:1c4e. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom@flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: not enabled 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes SPI Read Configuration: prefetching disabled, caching enabled, BIOS_CNTL = 0x02: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: Setting Bios Control at 0xdc from 0x02 to 0x01 failed. New value is 0x02. SPIBAR = 0x00007f08e08bd000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 SPI Configuration is locked down. Reading OPCODES... done OP Type Pre-OP op[0]: 0x9f, read w/o addr, none op[1]: 0x03, read w/ addr, none op[2]: 0x05, read w/o addr, none op[3]: 0x04, write w/o addr, none op[4]: 0x20, write w/ addr, none op[5]: 0x20, write w/ addr, none op[6]: 0x02, write w/ addr, none op[7]: 0x01, write w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x06 0x06: 0x3f00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x09ff0600 FREG1: BIOS region (0x00600000-0x009fffff) is read-write. 0x5C: 0x05ff0005 FREG2: Management Engine region (0x00005000-0x005fffff) is locked. 0x60: 0x00040001 FREG3: Gigabit Ethernet region (0x00001000-0x00004fff) is read-write. 0x64: 0x00001fff FREG4: Platform Data region is unused. Not all flash regions are freely accessible by flashrom. This is most likely due to an active ME. Please see https://flashrom.org/ME for details. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) At least some flash regions are read protected. You have to use a flash layout and include only accessible regions. For write operations, you'll additionally need the --noverify-all switch. See manpage for more details. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf84020 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=2, DBC=0, SME=0, SCF=0 0x94: 0x0606 (PREOP) 0x96: 0x7f48 (OPTYPE) 0x98: 0x0405039f (OPMENU) 0x9c: 0x01022020 (OPMENU+4) 0xa0: 0x00000000 (BBAR) 0xc4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xc8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xd0: 0x00000800 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040103 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 2 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH/SoC Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH/SoC Strap Base Addr): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x09300014 FLILL 0x00000000 --- Details --- Component 1 density: 8 MB Component 2 density: 2 MB Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x09ff0600 FLREG2 0x05ff0005 FLREG3 0x00040001 --- Details --- Region 0 (Descr. ) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00600000 - 0x009fffff Region 2 (ME ) 0x00005000 - 0x005fffff Region 3 (GbE ) 0x00001000 - 0x00004fff === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw Enabling hardware sequencing due to multiple flash chips detected. OK. The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Hardware sequencing reports 2 attached SPI flash chips with a combined density of 10240 kB. The flash address space (0x000000 - 0x9fffff) is divided at address 0x800000 in two partitions. The first partition ranges from 0x000000 to 0x7fffff. In that range are 2048 erase blocks with 4096 B each. The second partition ranges from 0x800000 to 0x9fffff. In that range are 512 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (10240 kB, Programmer-specific) mapped at physical address 0x0000000000000000. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x45, id2 0x08, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x45, id2 0x08, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x45, id2 0x08, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x45, id2 0x08, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x45, id2 0x08, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (10240 kB, Programmer-specific). No operations were specified. Restoring MMIO space at 0x7f08e08c08a0 Restoring PCI config space for 00:1f:0 reg 0xdc