Nick: neonsea
E-mail: neonsea@gitdrop.uk
Board: edgar
Contents: 
mint ~ # ./flashrom -V -r test.bin
flashrom v0.9.4 chromium.googlesource.com/chromiumos/third_party/flashrom : eb253da : Jul 30 2016 03:29:12 UTC on Linux 4.4.0-53-generic (x86_64)
flashrom was built with libpci 3.2.1, GCC 4.8.4, little endian
Acquiring lock (timeout=180 sec)...
Opened file lock "/run/lock/firmware_utility_lock"
Lock acquired.
Calibrating delay loop... OS timer resolution is 1 usecs, 819M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 991 us, 10000 myus = 10318 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "Google"
DMI string system-product-name: "Edgar"
DMI string system-version: "1.0"
DMI string baseboard-manufacturer: "Google"
DMI string baseboard-product-name: "Edgar"
DMI string baseboard-version: "1.0"
DMI string chassis-type: "Desktop"

Root Complex Register Block address = 0xfed1c000
get_target_bus_from_chipset() returns 0x8.
Found chipset "Intel Braswell" with PCI ID 8086:229c. Enabling flash write... Mapping BYT IBASE at 0xfed08000, unaligned size 0x200.

0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x100
Root Complex Register Block address = 0xfed1c000
Setting BBS to SPI
GCS = 0xc01: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap : enabled (A16 inverted)
SPI_BASE_ADDRESS = 0xfed01000
Mapping BYT SBASE at 0xfed01000, unaligned size 0x200.
SPIBAR = 0xfed01000 + 0x0000
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
WARNING: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x08: 0x00001000 (FADDR)
0x50: 0x00000a0b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b
0x54: 0x00000000 (FREG0: Flash Descriptor)
0x00000000-0x00000fff is read-only
0x58: 0x07ff0200 (FREG1: BIOS)
0x00200000-0x007fffff is read-write
0x5C: 0x01ff0001 (FREG2: Management Engine)
0x00001000-0x001fffff is locked
0x60: 0x00000fff (FREG3: Gigabit Ethernet)
Gigabit Ethernet region is unused.
0x64: 0x00000fff (FREG4: Platform Data)
Platform Data region is unused.
0x90: 0x80 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf80000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0
0x94: 0x0000     (PREOP)
0x96: 0x0000     (OPTYPE)
0x98: 0x00000000 (OPMENU)
0x9C: 0x00000000 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80800000 (LVSCC)
LVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=1
0xC8: 0x00000000 (UVSCC)
UVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=0
0xD0: 0x50444653 (FPB)

Enabling hardware sequencing because some important opcode is locked.
OK.
Programmer does not support specified bus
Error: Programmer initialization failed.
Restoring MMIO space at 0x7f9e5ce9c0a0
Restoring MMIO space at 0x7f9e5ce9d000
Restoring MMIO space at 0x7f9e5cea101c
restore_power_management: Re-enabling power management.