Nick: tix
E-mail: none
Board: Gigabyte HM97 - Aorus
Contents: 
Facing a opcode 0x03 

sudo ./flashrom -p internal:ich_spi_mode=swseq -c MX25L6406E/MX25L6408E -w X5BF.B07 -V
flashrom v0.9.9-r1955 on Linux 4.4.0-21-generic (x86_64)
flashrom is free software, get the source code at https://flashrom.org

flashrom was built with libpci 3.3.1, GCC 5.3.1 20160413, little endian
Command line (7 args): ./flashrom -p internal:ich_spi_mode=swseq -c MX25L6406E/MX25L6408E -w X5BF.B07 -V
Calibrating delay loop... OS timer resolution is 1 usecs, 3446M loops per second, 10 myus = 11 us, 100 myus = 105 us, 1000 myus = 995 us, 10000 myus = 9918 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: 85.
Found ITE EC, ID 0x8587, Rev 0x06 on port 0x4e.
Found chipset "Intel 9 Series" with PCI ID 8086:8cc3.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: enabled (A16(+) inverted)
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching enabled, caching enabled, 
BIOS_CNTL = 0x09: BIOS Lock Enable: disabled, BIOS Write Enable: enabled
SPIBAR = 0x00007f3ad78d8000 + 0x3800
0x04: 0xb008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=0, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x90: 0x04 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0xf84130 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=3, DBC=1, SME=0, SCF=0
0x94: 0x0006     (PREOP)
0x96: 0x8400     (OPTYPE)
0x98: 0x05000000 (OPMENU)
0x9C: 0x5a00019f (OPMENU+4)
OK.
The following protocols are supported: FWH, SPI.
Probing for Macronix MX25L6406E/MX25L6408E, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017
Found Macronix flash chip "MX25L6406E/MX25L6408E" (8192 kB, SPI) mapped at physical address 0x00000000ff800000.
Chip status register is 0x00.
Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set
Chip status register: Bit 6 is not set
Chip status register: Block Protect 3 (BP3) is not set
Chip status register: Block Protect 2 (BP2) is not set
Chip status register: Block Protect 1 (BP1) is not set
Chip status register: Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
This chip may contain one-time programmable memory. flashrom cannot read
and may never be able to write it, hence it may not be able to completely
clone the contents of this chip (see man page for details).
Flash image seems to be a legacy BIOS. Disabling coreboot-related checks.
Reading old flash chip contents... Invalid OPCODE 0x03, will not execute.
FAILED.
Restoring PCI config space for 00:1f:0 reg 0xdc