Nick: Smoluch
E-mail: smoluszek@gmail.com
Board: IPIEL-LA3
Contents: 
sudo flashrom -p internal -VVV -c W25X80
flashrom v0.9.7-r1711 on Linux 3.13.0-39-generic (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian
Command line (5 args): flashrom -p internal -VVV -c W25X80
Calibrating delay loop... OS timer resolution is 1 usecs, 1213M loops per second, 10 myus = 10 us, 100 myus = 94 us, 1000 myus = 936 us, 10000 myus = 9370 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "Hewlett-Packard"
DMI string system-product-name: "                                "
DMI string system-version: "                                "
DMI string baseboard-manufacturer: "PEGATRON CORPORATION"
DMI string baseboard-product-name: "2A94"
DMI string baseboard-version: "1.03"
DMI string chassis-type: "Desktop"
Found chipset "Intel ICH10" with PCI ID 8086:3a18. Enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode disabled
0xffe00000/0xffa00000 FWH decode disabled
0xffd80000/0xff980000 FWH decode disabled
0xffd00000/0xff900000 FWH decode disabled
0xffc80000/0xff880000 FWH decode disabled
0xffc00000/0xff800000 FWH decode disabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
BIOS_CNTL = 0x02: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
Warning: Setting Bios Control at 0xdc from 0x02 to 0x03 on ICH10 failed.
New value is 0x02.
Root Complex Register Block address = 0xfed1c000
GCS = 0x461: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x1 (SPI)
Top Swap : not enabled
SPIBAR = 0xfed1c000 + 0x3800
0x04: 0xa008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=0, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
        OP        Type      Pre-OP
op[0]: 0x02, write w/  addr, none
op[1]: 0x03, read  w/  addr, none
op[2]: 0x20, write w/  addr, none
op[3]: 0x05, read  w/o addr, none
op[4]: 0x9f, read  w/o addr, none
op[5]: 0x01, write w/o addr, none
op[6]: 0x06, write w/o addr, none
op[7]: 0x00, write w/o addr, none
Pre-OP 0: 0x06, Pre-OP 1: 0x00
0x08: 0x00000000 (FADDR)
0x74: 0x00000000 (PR0 is unused)
0x78: 0x00000000 (PR1 is unused)
0x7C: 0x00000000 (PR2 is unused)
0x80: 0x00000000 (PR3 is unused)
0x84: 0x00000000 (PR4 is unused)
0x90: 0x04 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0x004240 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=4, DBC=2, SME=0, SCF=0
0x94: 0x0006     (PREOP)
0x96: 0x543b     (OPTYPE)
0x98: 0x05200302 (OPMENU)
0x9C: 0x0006019f (OPMENU+4)
0xA0: 0x00000000 (BBAR)

checking for opcode 0x03
checking for opcode 0x05
SPI Read Configuration: prefetching disabled, caching enabled, PROBLEMS, continuing anyway
The following protocols are supported: FWH, SPI.
Probing for Winbond W25X80, 1024 kB: RDID returned 0xef 0x30 0x14. probe_spi_rdid_generic: id1 0xef, id2 0x3014
Found Winbond flash chip "W25X80" (1024 kB, SPI) at physical address 0xfff00000.
Chip status register is 0x00.
No operations were specified.
Restoring MMIO space at 0x7f06a08fd8a0
Restoring PCI config space for 00:1f:0 reg 0xdc