Nick: xvilka
E-mail: xvilka@gmail.com
Board: Intel DQ77MK
Contents: 
flashrom v0.9.6.1-runknown on Linux 3.8.2 (i686)
flashrom was built with libpci 3.1.9, GCC 4.7.2, little endian
Command line (11 args): ./flashrom -VVV -p internal --layout intel_dq77mk.layout --image me -r me.rom -o intel_dq77mk_layout_me.log
romlayout 00000000 - 00000fff named descr
romlayout 005c0000 - 00bfffff named bios
romlayout 00003000 - 005bffff named me
romlayout 00001000 - 00002fff named gbe
Looking for region "me" (file="<not specified>")... found.
Using region: "me".
Calibrating delay loop... OS timer resolution is 1 usecs, 3276M loops per second, 10 myus = 11 us, 100 myus = 99 us, 1000 myus = 1002 us, 10000 myus = 9974 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "                                 "
DMI string system-product-name: "                                 "
DMI string system-version: "                                 "
DMI string baseboard-manufacturer: "Intel Corporation"
DMI string baseboard-product-name: "DQ77MK"
DMI string baseboard-version: "AAG39642-401"
DMI string chassis-type: "Desktop"
Found chipset "Intel Q77" with PCI ID 8086:1e47. 
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
Warning: BIOS region SMM protection is enabled!
Warning: Setting Bios Control at 0xdc from 0x2a to 0x0b on Q77 failed.
New value is 0x2a.
Root Complex Register Block address = 0xfed1c000
GCS = 0xc65: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap : not enabled
SPIBAR = 0xfed1c000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
        OP        Type      Pre-OP
op[0]: 0x02, write w/  addr, none
op[1]: 0x03, read  w/  addr, none
op[2]: 0x20, write w/  addr, none
op[3]: 0x05, read  w/o addr, none
op[4]: 0x9f, read  w/o addr, none
op[5]: 0x01, write w/o addr, none
op[6]: 0x00, read  w/o addr, none
op[7]: 0x00, read  w/o addr, none
Pre-OP 0: 0x06, Pre-OP 1: 0x00
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x08: 0x00002fc0 (FADDR)
0x50: 0x00000a0b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b
0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
0x58: 0x0bff05c0 FREG1: BIOS region (0x005c0000-0x00bfffff) is read-write.
0x5C: 0x05bf0003 FREG2: Warning: Management Engine region (0x00003000-0x005bffff) is locked.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.
0x64: 0x00001fff FREG4: Platform Data region is unused.
0x74: 0x00000000 (PR0 is unused)
0x78: 0x00000000 (PR1 is unused)
0x7C: 0x00000000 (PR2 is unused)
0x80: 0x00000000 (PR3 is unused)
0x84: 0x00000000 (PR4 is unused)
Please send a verbose log to flashrom@flashrom.org if this board is not listed on
http://flashrom.org/Supported_hardware#Supported_mainboards yet.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0x80 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf94010 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=0, SME=0, SCF=1
0x94: 0x0006     (PREOP)
0x96: 0x043b     (OPTYPE)
0x98: 0x05200302 (OPMENU)
0x9C: 0x0000019f (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0
0xD0: 0x00000000 (FPB)

Reading flash descriptors mapped by the chipset via FDOC/FDOD... done.
=== Content Section ===
FLVALSIG 0x0ff0a55a
FLMAP0   0x03040103
FLMAP1   0x12100206
FLMAP2   0x00210120

--- Details ---
NR          (Number of Regions):                     4
FRBA        (Flash Region Base Address):         0x040
NC          (Number of Components):                  2
FCBA        (Flash Component Base Address):      0x030
ISL         (ICH/PCH Strap Length):                 18
FISBA/FPSBA (Flash ICH/PCH Strap Base Address):  0x100
NM          (Number of Masters):                     3
FMBA        (Flash Master Base Address):         0x060
MSL/PSL     (MCH/PROC Strap Length):                 1
FMSBA       (Flash MCH/PROC Strap Base Address): 0x200

=== Component Section ===
FLCOMP   0x0930001c
FLILL    0x00000000

--- Details ---
Component 1 density:             8 MB
Component 2 density:             4 MB
Read Clock Frequency:           20 MHz
Read ID and Status Clock Freq.: 33 MHz
Write and Erase Clock Freq.:    33 MHz
Fast Read is supported.
Fast Read Clock Frequency:      33 MHz
No forbidden opcodes.

=== Region Section ===
FLREG0   0x00000000
FLREG1   0x0bff05c0
FLREG2   0x05bf0003
FLREG3   0x00020001
FLREG4   0x00001fff

--- Details ---
Region 0 (Descr.) 0x00000000 - 0x00000fff
Region 1 (BIOS  ) 0x005c0000 - 0x00bfffff
Region 2 (ME    ) 0x00003000 - 0x005bffff
Region 3 (GbE   ) 0x00001000 - 0x00002fff
Region 4 (Platf.) is unused.

=== Master Section ===
FLMSTR1  0x0a0b0000
FLMSTR2  0x0c0d0000
FLMSTR3  0x08080118

--- Details ---
      Descr. BIOS ME GbE Platf.
BIOS    r     rw      rw     
ME      r         rw  rw     
GbE                   rw     

Enabling hardware sequencing due to multiple flash chips detected.
SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Not mapping flash chip, zero size at 0x00000000.
Found 2 attached SPI flash chips with a combined density of 12288 kB.
There is only one partition containing the whole address space (0x000000 - 0xbfffff).
There are 3072 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific) at physical address 0x0.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific).
Reading flash... Reading "me" 0x00003000 - 0x005bffff (6017024B)... Reading 6017024 bytes starting at 0x003000.
Transaction error between offset 0x00003000 and 0x0000303f (= 0x00003000 + 63)!
HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
failed. Read operation failed!
FAILED.
Restoring MMIO space at 0xb76e18a0
Restoring PCI config space for 00:1f:0 reg 0xdc