Nick: cjt
E-mail: http://pastebin.com/G06ZrRyT
Board: cjt
Contents: 
flashrom v0.9.6.1-runknown on Linux 2.6.38-2-486 (i686)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.1.9, GCC 4.7.2, little endian
Command line (5 args): ./M2NX1004/neuste/flashrom/flashrom -w M2NX1004/M2NX1004.ROM -V -p internal
Calibrating delay loop... OS timer resolution is 1 usecs, 1306M loops per second, 10 myus = 10 us, 100 myus = 101 us, 1000 myus = 1001 us, 10000 myus = 10007 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "System manufacturer"
DMI string system-product-name: "System Product Name"
DMI string system-version: "System Version"
DMI string baseboard-manufacturer: "ASUSTeK Computer INC."
DMI string baseboard-product-name: "M2N-MX"
DMI string baseboard-version: "Rev 1.xx"
DMI string chassis-type: "Desktop"
Found ITE Super I/O, ID 0x8712 on port 0x2e
Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork...
ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0
Flash bus type is LPC
Found SMBus device 10de:03eb at 00:01:1
MCP SPI BAR is at 0x00000000
MCP SPI is not used.
Please send the output of "flashrom -V" to flashrom@flashrom.org with
your board name: flashrom -V as the subject to help us finish support for your
chipset. Thanks.
OK.
Super I/O ID 0x8712 is not on the list of flash capable controllers.
Enabling full flash access for board "ASUS M2N-MX"... Using IT87 GPIO base 0x0a00
OK.
The following protocols are supported: LPC.
Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xb0, id2 0x29, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xda, id2 0x50
Found Winbond flash chip "W39V040C" (512 kB, LPC) at physical address 0xfff80000.
Lockout bits:
Hardware bootblock locking (#TBL) is active.
Hardware remaining chip locking (#WP) is active..
Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xda, id2 0x50
Found Winbond flash chip "W39V040C" (512 kB, LPC).
Flash image seems to be a legacy BIOS. Disabling coreboot-related checks.
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0... 0x000000-0x00ffff:EERASE FAILED at 0x0000000c! Expected=0xff, Read=0x08, failed byte count from 0x00000000-0x0000ffff: 0xfdf9
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 1... 0x000000-0x07ffff:EERASE FAILED at 0x0000000c! Expected=0xff, Read=0x08, failed byte count from 0x00000000-0x0007ffff: 0x73ab8
ERASE FAILED!
Looking for another erase function.
No usable erase functions left.
FAILED!
Uh oh. Erase/write failed. Checking if anything changed.
Good. It seems nothing was changed.
Writing to the flash chip apparently didn't do anything.
This means we have to add special support for your board, programmer or flash chip.
Please report this on IRC at irc.freenode.net (channel #flashrom) or
mail flashrom@flashrom.org!
-------------------------------------------------------------------------------
You may now reboot or simply leave the machine running.
Restoring PCI config space for 00:01:0 reg 0x6d
Restoring PCI config space for 00:01:0 reg 0x90
Restoring PCI config space for 00:01:0 reg 0x8c
Restoring PCI config space for 00:01:0 reg 0x88